1/72 AH-1Z

1
August 28, 2023
2
August 28, 2023
3
August 28, 2023
The quality is Okey, I was hopeing for more details though.
4
August 28, 2023
5
August 28, 2023
6
August 28, 2023
first time try 3D decal, quite easy to use.
7
August 28, 2023
8
August 28, 2023
cockpit done
9
August 28, 2023
The default camera turret doesn't have any details. So I have add by myself.
10
September 2, 2023
I am going to call this a bad design. It is not possible to fill the gaps that are out of reach.
11
September 2, 2023
12
September 2, 2023
not sure why there are lines on LAU61 rocket pad. There isn't any on photos
13
September 2, 2023
more fillings for the gaps
14
September 2, 2023
these bolts are way too big for this scale. Not sure why does the manufacturer designed this way. A simple dots like others is good enough
15
September 2, 2023
another overly exaggerated bolts
16
September 2, 2023
The turret given by the kit is also quite poor. It doesn't give anything for the mechanical parts within, so I have to do it myself. What's worse is that the shape of the turret is also a bit off.
17
September 2, 2023
drill through suppose to transparent windows.
18
September 2, 2023
added some minor details such as bolts etc.
19
September 2, 2023
now I am certain this rocket pad is a joke. The front doesn't not represent the real thing at all despite have decent details. It is very obvious if compared with LAU61's photos side by side.
20
September 2, 2023
21
September 2, 2023
turret done
22
September 5, 2023
since the exhaust is hopelessly difficult to sand it. I decided to make the internala with copper sheet by my own
23
September 5, 2023
The most outer layer is 0.1 abs sheet and rest of it is the part I made in previous photo. The final result is worth the effort.
24
September 5, 2023
applying PE parts. The kit actually has pits for all the PEs, which is quite nice.
25
September 5, 2023
26
September 5, 2023
puttying this section
27
September 5, 2023
made this tube with copper sheet. I soldered it for extra strength.
28
September 5, 2023
looks a lot better than the original one
29
September 5, 2023
add small details on the side wings
30
September 5, 2023
more polishing before next steps
31
September 11, 2023
Add a bit detail to the landing gear
32
September 11, 2023
patty work
33
September 11, 2023
installing sidewings
34
September 11, 2023
adding wires to the tail propeller motor
35
September 11, 2023
side view
36
September 11, 2023
masking the internal of the cockpit window for paint black color. It can be clearly seen in photos that there are two layers of color here.
37
September 11, 2023
ready to be painted
38
September 11, 2023
39
September 11, 2023
40
September 11, 2023
while waiting for good weather for painting, I am polishing the propeller blades to make it shaper which is closer to the realy thing
41
September 11, 2023
tail propeller also requires some work
42
September 11, 2023
I lost one of the PE part for the front nose oil injector(no sure what it is to be honest), so I have to make one from coppor sheet.
43
September 11, 2023
looks all right
44
September 11, 2023
the painting nearly done, the color scheme from the kit is not good. The upper parts is suggested with C337 which is no where close to the color in photos. SoI have to adjust it with green gray paint.
45
September 11, 2023
decal done. The kit's decal is quite good. Very thin and in good quality. The only cons is it too hard to apply as it would warp around the tong I use due to how thin it is.
46
September 24, 2023
47
September 24, 2023
48
September 24, 2023
49
September 24, 2023
50
September 24, 2023
51
September 24, 2023
weathering
52
September 24, 2023
initial weathering blades, later brush them more with second layer
53
September 24, 2023
the rack adapter need a bit work for eduard hellfire
54
September 24, 2023
weapons and loads
55
September 24, 2023
the eduard hellfire is a lot harder to assemble than I anticipated. good details though. Lost one of the transparent cap, hence one less rocket.
56
September 24, 2023
57
September 24, 2023
nearly done, need a bit more fine tuning and a base as w
58
October 5, 2023
59
October 5, 2023
60
October 5, 2023
61
October 5, 2023
62
October 5, 2023
63
October 5, 2023
64
October 5, 2023
65
October 6, 2023
66
October 6, 2023
67
October 6, 2023
68
October 6, 2023
69
October 6, 2023
70
October 6, 2023
71
October 6, 2023
72
October 6, 2023
73
October 6, 2023
74
October 6, 2023
75
October 6, 2023
76
October 6, 2023
77
October 6, 2023
78
October 6, 2023
79
October 6, 2023
80
October 6, 2023
81
October 6, 2023
82
October 6, 2023

Kommentare

53 28 August 2023, 04:31

Oleg Bogolei
Following!

28 August 2023, 06:36

Finn
Will follow

2 September 2023, 08:22

Naram
Look very sharp and neat building. Folllowing

4 September 2023, 13:58

Rui S
Very nice paintjob 👍

16 September 2023, 22:17

Dietmar Kollmann
The figures looks very good. Which company are they?

5 October 2023, 06:08

Harry Eder
Looks very promising! Great job! 👍

5 October 2023, 08:14

Hang Li Autor
Thank you all for the support. As for the figures, I purchased them from a local 3D printing shop listed on the domestic version of Aliexpress.

5 October 2023, 08:38

Neuling
Top dio in good presentation!

6 October 2023, 06:56

Łukasz Gliński
Impressive dio indeed 👍

6 October 2023, 08:56

Cristian A
Impresive work on the AH-1Z Viper, well achieved ! 👍

9 April, 20:25

Rui S
Beautiful Dio 👍

9 April, 21:44

Frank Brzobohaty
Love that in picture number 81, the guy is marshalling the rolling hellfire middle.

10 April, 00:33

Album info

My first helicopter. This kit seems to have good quality, so hopefully a good starting point. I am planning on doing this project while waiting for the mig29 nozzles.

Not sure if there is any interesting paint scheme for this hovering bird, and I don't think I can get the corresponding decals anyway. So peobably just do the default one in the box.

1/72 Bell AH-Z1 Viper

82 Bilder

1:72

Fertiggestellt

1:72 AH-1Z Viper - interior 3D decals (Kelik K72025)

1:72 AH-1Z 'Viper' (DreamModel DM 720012)

Alle Alben

Alle Alben anzeigen »