Hilo iniciado por DesertMarlin
Desert MarlinNuevo álbum de fotos añadido
99 8 November 2023, 21:10
Desert Marlin AutorThis project will have both pilots on the intercom and watching the engine startup process. That is why the same type figure is used in both cockpits. They both monitor the engine to ensure that the EGT and RPM is increasing appropriately. Each has their hand on the control stick to be able to open their MIC as they confirm everything is normal at start. The plan is to have the aircraft loaded with a Nuke (Apache Cruise Missile?). Seems appropriate to me for the days we live in now...
8 November 2023, 22:16
Desert Marlin AutorHave to pause this one until I get the BIG ED kit #33216...
9 November 2023, 00:59
TreehuggerMaybe go for resin seats as well?
Seems like kit plastic never can compete with resin seats. 🙂
Though, I no longer crave for resin interior for the cockpit because of the work, but seats are ok.
9 November 2023, 05:17
Desert Marlin AutorI'll paint these up and see if I can tolerate them. If they are too bland, I have time to change my mind! Thanks for the idea!
9 November 2023, 21:25
Desert Marlin AutorGreat video of the weapon that goes with this version of the Mirage 2000N
Youtube Video
25 November 2023, 00:46
Desert Marlin AutorI got the ResKit Mirage 2000N Cockpit Set (Detailed Version).
14 July 2024, 01:55
Desert Marlin AutorAs I have begun work on this kit, I am yet again struck by the lack of information in the variations and options provided in the kit. For example, the tail tip is not called out that applies to the 2000N version. While the nose of the 2000D is provided in the kit, it has to be modified to make it correct for the 2000N. Oh bother…
20 July 2024, 02:40
Desert Marlin AutorSelected "most appropriate" tail tip and mounted the correct nose to fuselage.
21 July 2024, 20:04
Desert Marlin AutorOkay, now I'm excited to get some paint on this cockpit!!! ResKit, you guys have done some great work with your 3D Resin Printing!
16 August 2024, 18:29
TreehuggerOh, did you fiddle with the nose part to make it match the N version, or did you have to buy aftermarket nose for the N version? I have this kit in my stash, but haven't really looked any it yet.
28 August 2024, 05:43
Desert Marlin AutorI'm using the D nose but converting it to an N version. I'm also closing the "sucker doors" on the inlets to represent an engine that is not yet started... I'm assuming initial hydraulic power is applied from the APU and auxiliary hydraulic pumps have brought the gear door up. I'm going to close the speed breaks for pre-engine start configuration...
28 August 2024, 17:36
Eric ThorntonLooks like BAM has some corrected noses still need the N one. Maybe reach out to him. I could use the corrected nose for this kit also. The Reskit stuff looks amazing.
bam-models.com/produ..2000-corrected-nose/
30 August 2024, 13:57
Desert Marlin AutorThanks for the heads up! The BAM nose looks fantastic! Sadly, the 2000N nose has a pitot tube and does not have the RDY antenna lines. It seems that much of the 2000N systems are somewhat earlier than the -5 systems. Everything I can find on the 2000N seems to be somewhat austere compared with the 2000-5. The ResKit cockpit is worth every penny!
30 August 2024, 14:59
Mr DLike it 😀👍
Nice when the pilot looks like he's actually doing something and engaged with the craft.
30 August 2024, 15:22
Desert Marlin AutorThanks. It's really sad to remove detail from the ejection seat, but that is the only way to get the pilot in place...
30 August 2024, 22:47
Desert Marlin AutorThe pilot is from REEDOAK. They have several different figures in various poses so the realism can be developed based on the aircraft scenario. This model is being build to represent events just prior to engine start.
31 August 2024, 01:50
Desert Marlin AutorRemaining cockpit items:
1. Glass
2. Decals on seats
3. A little more weathering
4. Fix pilot's France Flag
5. Add WSO's Right shoulder patch
6. Check that I can get the canopy actuators in after everything is assembled...
7. Add HUD glass
1 September 2024, 03:07
Desert Marlin AutorThe glass and HUD went in great! I had to lightly sand the edge of the glass to get it to fit snugly into the ResKit frame between the front and back seats. I used 1000 grit and lightly buffed all the way around the edge. Fits perfectly!
3 September 2024, 16:01
Desert Marlin AutorCockpit is done! Looks like the ResKit cockpit tub fits perfectly! Lots of trimming to get the crew in the proper fit. Right now, I think it's ready for final checks before fuselage join. The forward control panel needs some sanding for fit, but it does work. I have left the seats, pilots and control panels loose until final fuselage join just to have "wiggle room" before closing. I was able to adjust the forward control stick to make it match the pilot's hand more closely. Just need to check a few more things and then join the fuselage halves!
4 September 2024, 22:19
Desert Marlin AutorThanks! I can't believe this version of the 2000 is so "old"...
5 September 2024, 20:17
Laurent VILLANUEVA HELLER ForEverattention aux couleurs sur les notices kinetic etc , certaines sont fausses!
5 October 2024, 11:29
Dave FlittonThe pilots look like they are impatiently waiting for you to finish the aircraft so that they can fly!
6 October 2024, 00:31
Desert Marlin AutorI got the canopy frames in the mail. The "detchord" in the forward canopy is perfect!
14 October 2024, 21:27
Mr DDone a really smart job on cockpit n pilots 😁👍
It will be show peice of the Aircraft so worth the effort,
Did you have decals for the green display screen's ??
14 October 2024, 21:43
Desert Marlin AutorScreens are aluminum paint with clear green over the aluminum.
16 October 2024, 02:58
Desert Marlin AutorIJN Green is NOT the correct green for these planes. Sorry Kitty Hawk, just not right...
28 October 2024, 01:29
Desert Marlin AutorSmall Disaster. Soured Paint/Gloss has occurred. I'm a little bummed. It takes longer to get everything finished!
29 October 2024, 18:15
Desert Marlin AutorUsing water and a paper towel(s), I am able to verify where the soured paint/gloss has occurred. It has to be removed since the decal process will definitely find the errors during application. If the coating cannot stand water, it will never support the markings...
29 October 2024, 18:20
Desert Marlin AutorPanel line accent applied. Need to review and clean up anything out of place and then apply some poly to get ready for markings! Also need to fix the wing slats on the left wing. The method for mounting these slats is really weak...
2 November 2024, 04:08
Desert Marlin AutorPretty much done. I need to research a little bit, but there is history between the USA and France where the indigenous peoples are concerned. Suffice it to say that this image of an Indigenous Chief at the Wailing Wall and this particular Mirage 2000N seem to intersect just a little bit.
8 November 2024, 03:28
Desert Marlin AutorMore pictures tomorrow evening. The build is essentially done at this point so more pictures are needed! Cheers!
8 November 2024, 03:28
Desert Marlin AutorThanks! I had a tremendous amount of trouble with the painting...
10 November 2024, 05:19
Desert Marlin AutorThank you all! BTW, the shark mouth was not supposed to cross the formation lights, but, alas, it does...
11 November 2024, 01:11
Rui SBaeutifully result and outcome on this BIIGGG bird. Really like photo 2 👍
17 November 2024, 22:20
Desert Marlin AutorThanks Rui! Really the material from ResKit and REEDOAK are just first rate!
17 November 2024, 22:21
bughunterVery nice model 👍 I like the pilots.
The workbench is nice and tidy, but this great model deserves a few nice photos against a suitable background!
17 November 2024, 22:48
