Polikarpov I-16 Type 24 (WIP)

1
February 17, 2018
2
February 17, 2018
3
February 17, 2018
4
February 17, 2018
Some added detail with lead wire
5
February 17, 2018
Interiors varnished with Tamiya X-22
6
February 17, 2018
7
February 19, 2018
After a wash and matt varnish, I cut the floor sides, to be more accurate and then closed the halves
8
February 19, 2018
9
February 19, 2018
Difficult fit is the wings
10
February 20, 2018
Some difficult joins at wing roots; I put a small sprue piece inside to open the cowl a little to improve the fit, I'll remove it after glue dries
11
February 25, 2018
Some putty and AK primer
12
February 27, 2018
Pre-shading
13
February 27, 2018
14
March 11, 2018
15
March 11, 2018
The parts around the oleo have a strange position, but reference photos do show them very wide open
16
March 11, 2018
17
March 16, 2018
Installed a black palsticard wall through the middle of the engine, so that light does not pass from one side to the other, through the exhausts openings
18
March 23, 2018
Varnished with X-22 and ready for decals
19
March 23, 2018
First decals - very good fit
20
March 25, 2018
21
March 25, 2018
22
April 16, 2018
Wash with Panel Line Wash A.MIG-1608
23
June 26, 2018
Painting bits and pieces
24
June 28, 2018
Wash with Panel Line Wash A.MIG-1610
25
July 4, 2018
First oils applied on top
26
July 4, 2018
First oils applied on the bottom
27
July 6, 2018
Glued the "thing"...
28
July 14, 2018
A correction was needed to hide the central join, is was becoming visible
29
July 14, 2018
30
July 22, 2018
Some chipping on the propeler
31
July 22, 2018
32
July 22, 2018
33
July 22, 2018
Propeler, canopy and door assembled
34
July 22, 2018
Glueing the wheels
35
July 22, 2018
36
September 1, 2018
Preparing the base
37
September 1, 2018
Painting the base with the first colours
38
September 2, 2018
39
September 4, 2018
Glueing the covers of the landing gear - difficult task, to say the least
40
September 4, 2018
41
September 4, 2018
Test fit in the base
42
September 7, 2018
Test fit of a few additional elements
43
September 7, 2018
Finished
44
September 8, 2018

Comentarios

17 February 2018, 18:45

Soeren R.
Count me in😉

20 February 2018, 06:54

Guy Rump
Looking good 🙂

20 February 2018, 08:36

Ricardo Reis Autor
👍

20 February 2018, 10:02

David Thor
Taking a seat!

27 February 2018, 06:57

Ricardo Reis Autor
Kit is really nice. Could probably have a better fuselage and wings fit, but no big deal - really fast build, that I'm doing while waiting for the paints of the F/A-18 and Mig-21 builds to dry! 🙂

27 February 2018, 09:34

Dan Cook
I have had the same issue with getting the wings to fit. I had to use some sprue in the cockpit area to spread the nose to fit the wings. I have boxed it up at the moment and I am going to come back to it. Frustrated me so lost my mojo a bit on it.

16 March 2018, 10:00

Ricardo Reis Autor
Yes, the macro fit is a bit messy, but I think it is not as bad as it seems. Furthermore, the join lines are aligned with natural panel lines, so you can get away with a lot of messy repairs. Because of this, I used more Plastic Perfect Putty than I usually do, because it is quite easy to apply and clean with water, without much worried about sanding afterwards! 🙂

16 March 2018, 14:56