Wyvern

1
June 2, 2020
2
June 2, 2020
3
June 2, 2020
4
June 2, 2020
5
June 2, 2020
6
June 3, 2020
Construction started with the well detailed cockpit
7
June 3, 2020
Cockpit together
8
June 3, 2020
Cockpit painted in Revell anthracite. Details dry brushed with white and silver.
9
June 3, 2020
10
June 3, 2020
The seat was made up of several parts and very nicely detailed
11
June 3, 2020
The only thing missing were the ejection handles. I made some from some wire. Not brilliant and I think I'd do it differently next time
12
June 3, 2020
13
June 3, 2020
Seat and cockpit together
14
June 3, 2020
15
June 3, 2020
16
June 3, 2020
I also made some seat straps from painted Tamiya masking tape with a buckle made from a piece of PE fret
17
June 3, 2020
18
June 3, 2020
Centre wing section up next
19
June 3, 2020
Top sections mated to lower section
20
June 3, 2020
The engine/props were painted before installation otherwise they may have been awkward to do cleanly
21
June 3, 2020
Decided on wings unfolded. The outer sections join to the centre section with a couple of pegs each side. The horizontal stabilisers don't have their distinctive dihedral if installed how the kit is manufactured. Easy to remedy with a small file though.
22
June 3, 2020
Wings and stabs on. Canopy on and masked with cockpit interior colour sprayed on.
23
June 3, 2020
Everything primed with Ammo Mig One Shot black primer.
24
June 3, 2020
Adding marbling with white. Splotchy in places as I was having issues with tip-dry.
25
June 3, 2020
26
June 3, 2020
Wing top surface colour going on. My first time using Ammo Mig paints. Took a bit of getting used to. This top colour wasn't too bad, but the lower surface colour was a nightmare to get without orange peel.
27
June 3, 2020
28
June 3, 2020
29
June 3, 2020
30
June 3, 2020
31
June 3, 2020
As I said in one of the other captions, this 'sky' colour was really difficult to get a good finish on without any orange peel. I had to spray it in really thin coats and allow a few minutes between each one
32
June 3, 2020
33
June 3, 2020
I wish more manufacturers did this!
34
June 3, 2020
Painting flaps, airbrakes, gear doors and drop tanks
35
June 3, 2020
36
June 3, 2020
This was my first time using Ammo Mig Glossy Lucky Varnish and I won't be using it again. I used it as per the instructions with at 17psi and building up in thin coats. I lost count of how many coats went on, but maybe 8 in some places. And even then it wasn't overly glossy. Plus I ran into problems further down the line....
37
June 3, 2020
First decals on.
38
June 3, 2020
39
June 3, 2020
40
June 3, 2020
41
June 3, 2020
The varnish started peeling in places when I was applying the decals with Microset and Microsol. Someone on Instagram told me to watch out for it peeling. It had been left to dry for about 24 hours before I started decalling. I wasn't best pleased.
42
June 3, 2020
Flaps and gear doors on
43
June 3, 2020
For weathering I tried to steer clear of enamel washes and white spirit because of the issues I had with the varnish, so a lot of it was done with pigments

Komentarzy

4 2 June 2020, 21:47

Ben M
The panel lines and weathering in this looks "just right" to me.

2 June 2020, 22:33

R VG
You don't see a Wyvern much. Quite an impressive model and very detailed in 1/72 scale!

2 June 2020, 22:53

Sparky Rogers Autor
Thanks Ben. I'm pleased with how it turned out. It was my first time using Ammo Mig Glossy Lucky Varnish and I don't rate it at all. It made doing the panel lines difficult.

R VG it's a great kit. Fantastic interior details too. The propeller assemblies aren't glued together. In theory you can take the props and hubs apart as there's lots of detail in those too. There are some details that Trumpeter got wrong but they're easily fixable.

Thanks Roland. A very interesting model indeed!

3 June 2020, 08:37

Łukasz Gliński
That's a nice one, but deserves a better background for sure 👍

3 June 2020, 12:15

Dave Flitton
Thanks for the in-build photos. well done!

3 June 2020, 12:38

Neuling
Very good looking! Your subtle weathering is absolutely convincing.

3 June 2020, 16:19

Sparky Rogers Autor
Yeah, I really should find a better background to photo my finished builds against!

I've just added some more in-build pictures.

Thank you Neuling, most kind

3 June 2020, 18:15

Project info

Trumpeter Westland Wyvern

43 zdjęć/zdjęcia

1:72

Gotowe

Westland Wyvern S.4

Royal Navy Fleet Air Arm (1937-now)
No. 813 NAS WL879 / 278
1958 - HMS Eagle

Wszystkie albumy

Wyświetl wszystkie albumy »