Jaguar E-Type with headlights (maybe taillights?)

1
January 2, 2024
As usual with these kits, all the parts needed varying amounts of clean up, but I enjoy that bit in a strange way
2
January 2, 2024
Things never fit together as well as you hope they will, but this looks OK
3
January 2, 2024
I'm hoping I can fit some thin wires in between these door cards and the outer bodyshell, but that might be hoping too much, we'll see...
4
January 2, 2024
I need to make the sub-assemblies and then fit them so I can work out where the electrical bits go. Then paint some bits and hopefully fit things in without mucking it up too much
5
January 2, 2024
My first thought on location. The battery would be very visible here and mean I couldn't fit the seats.
6
January 2, 2024
Trying to see if the battery will sit either here or inside the sub-frame cleanly, and it does, so that's better. It was at this point that I realised I can't put the charging circuit there as it won't be possible to charge it, because the wheel and the body will be in the way, so more thinking needed!
7
January 2, 2024
The charging circuit fits cleanly here though, I will just need to glue it very solidly, so it doesn't come away when it is used to charge
8
January 2, 2024
I need to cut the black bits away for the charging port
9
January 2, 2024
Test fit with battery and charging circuit in place
10
January 2, 2024
You can see the battery here; it fits fine and will be blocked by the dashboard, which is the worst piece in the kit, but ho-hum...
11
January 2, 2024
Now I need to work out where the switch goes and try to fit some wires and possibly some resistors in somewhere...
12
January 2, 2024
I've decided to site the switch here, behind the seats, It will be seen if you look, but it won't be that obvious.
13
January 2, 2024
I just need to be careful when switching it on and off, and use both hands.. Let's face it, this won't be done much, all of this is just a bit of fun...
14
January 2, 2024
I did toy with the idea of placing a piece of styrene behind the seats, but once everything including the roof is painted I don't think it'll matter too much. I'm going to have to leave this for a bit now, will come back at the weekend, and start trying to think about the wires.
15
January 11, 2024
Very mild update; a few sundries painted while I wait to receive some thin electrical wire, which I've just realised won't arrive before I go away for a week, so this won't get attention until later this month...
16
January 22, 2024
Another mild update, back from holiday, wire and some electrical connectors (that I think may be too big to fit, I need to try them and see) and some painting done. I just need to find some time to put it back together and add the electrical components and see how much soldering I can try to avoid...
17
January 28, 2024
18
January 28, 2024
19
January 28, 2024
Some more progress, pretty much everything painted (correctly, now I think, I did some bits black that should be red first time...) trying to get the headlights in place; I bought some little connectors in an attempt to avoid soldering wires together, but they may not fit, so I got bored and stopped for a bit...
20
January 28, 2024
I'll pick it up once I've worked out if the connectors will fit or not, otherwise it's time for the soldering iron...

11 2 January 2024, 09:06

Spanjaard
interesting

2 January 2024, 09:32

alessandro magrelli
Cool. Where did you get that led kit?

2 January 2024, 12:18

Dexi Goodchild 著者
Hi Alessandro - I get LEDs from eBay - Bright Components have everything you might need. The batteries I also buy on eBay, just search for 3.7v lithium polymer battery and you should find plenty in different MAh ratings. The charging circuits I usually get on Amazon, but I bet you could also get them on eBay as well; Hayatec TP4056 are the ones I have been using... 😉

3 January 2024, 08:25

alessandro magrelli
Thanks a lot!

3 January 2024, 19:52