Wonga Bonga

Rui S
I'm in.😎

Peter Jenssen 著者
Welcome Rui!
I think the Sopwith Camel is the WnW model with the most cockpit rigging I have. (clearly I don't have the felixstowe 😉 )
Surprising for such a small plane.
Starting on the bent undershield, 9 cables already!

Rui S
I've 2 in my stash but unfortunately, no Wingnut Wings.
I'm a Panzer and other vehicles guy.
I also like the WWI and some WWII planes (but with almost none experience in these 1/32), so mainly I'm here to learn and enjoy😉
P.s. The rigging, looks to me, as the most difficult part?

Peter Jenssen 著者
Yes, I would probably agree there. Especially this kind of tiny cockpit rigging where you have to plan in detail how to go about it in order to reach and get the right tension in every bit.
I'm using Ezline, which is quite good.
The build and fit part of these kits is the easiest. With the WnW kits, the decalling can be a bit tricky. Not that there's anything wrong with the decals, -on the contrary. The decals are excellent. The challenges lie more in the size of the decals; -Some are extremely tiny and some huge.

Mike Daniels
Hi Peter definitely following along. I have just taken the plunge with WnW with the 'Le Rhone' Camel which is on order. Happy bunny. I thought the rigging didn't look too bad on the Camels but now you have me worried!! That cockpit looks fab.

Peter Jenssen 著者
Hi Mike,
I look at the interior rigging more like an experience and an excercise. Not much of it will be visible I suspect.
I would not be worried leaving bits of it out.
The tail could get a bit tricky I suspect, but nothing serious as far as I can tell.
Looking forward to following your Le Rhone Camel build!
Should be very little difference, except for the engine?

Peter Jenssen 著者
Here's a picture of interior rigging so far

Martin Oostrom
Rigging can be very tricky. Tom Grigat's got some tips: Youtube Video & Youtube Video

You can glue the EzLine or some other wire with superglue to the turnbuckle.

Mike Daniels
Are all those 'cables' at the bottom for the flaps/rudder etc ? rather than rigging per se ? Nice video Martin. I have seen Toms work before. Gives a very nice finish.

Peter Jenssen 著者
Hi Martin,
Thanks for the video links.
I have seen some from Uschi van der Rosten before. While you can certainly use turnbuckles on the internal cross bracing for the Camel, you have to be careful.
Firstly, for wing rigging, the Camel does not have turnbuckles.
Secondly, you have to be careful, or they will look out of scale.
Neat and cool looking detail, but out of scale.
I may simulate turnbuckles later on one of the larger German planes, using brass tubing..

Martin Oostrom
Peter, whatever turns you on (intentional joke) 🙂
The video's were merely intended as inspirational, but I guess you knew that. I really like where you're going and I will follow this build as closely as possible. Keep it up 👍

Peter Jenssen 著者
Hi Mike,
The rudder controls contribute most of the cables here.
Each side of the rudder has two cables, plus one extra for steering the tail skid(!)
So 6 in total for the rudder.
The elevator has four cables in this picture.
Reason for this is the elevator cables run through two pulleys attached to the cross beam behind the air intake.
The middle ones will go to the control stick, the outer ones back to the elevator.
The aileron cables you can barely see.
They go from the top of the horn on the joystick axle, and down to the leading edge of the wing (where it later can be seen through an inspection window)
Lastly, the three cables attached to the aluminium is a representation of bracing cables that really should go through.
The middle one is for the landing gear. The ones on the sides are for floor cross bracing.
I have cheated a bit here and drilled through all floor timbers to just zig-zag all the floor cross bracings with two wires...
(so yeah, makes for a total of 15 lose ends on this last picture! That's before installing the joystick. Sadly, you'll see very little of this detail on the completed model)

R VG
I'm not on this level. When you think of it, you need many of the same skills as a surgeon to pull this off!!

Mike Daniels
Nice one Peter. Did you learn all of that from the WnW documentation or from previous experience ? That is amazing attention to detail. I must admit that I would be tempted to only put in those you can actually see. But I can see the attraction of trying to create an as authentic model as possible. Its usually pretty difficult to get your hands on that sort of high detail information ( unless you happen to have a Camel in your garden). Thats 1/32 i suppose. Mine is in the post - gulp!

Peter Jenssen 著者
I installed the fairlead beam so i could pull back on the cables leading aft.
Now I can at least see what I'm doing.
Also temporarily removed the air intakes which I luckily didn't glue.
Now I can use it's attatchment hole to pull at the landing gear bracing.. 🙂

Peter Jenssen 著者
Hi Mike,
The most of it is, as you will see, in the build instructions!
The WnW instruction booklet contains a wealth of information. There is a rigging diagram for the cockpit, as well as photos of a Camel during renovations at Vintage Aviator.
(seep pg 5 of the instructions: wingnutwings.com/ww/..uctid=3157&cat=4 )
There are also additional photos on the website:
wingnutwings.com/ww/..uctid=3157&cat=2

Mike Daniels
Thanks Peter. Getting good authentic info is so helpful, especially on WW1 aircraft as so few photos exist.

Peter Jenssen 著者
Wicker seat and tank done. Dryfitting in cockpit. Joystick also done. Next: seatbelts, then time to glue this cockpit together..

Peter Jenssen 著者
I can see two sinkholes on top of the framing! Shock horror!
-Better now than after closing the fuselage I guess.. :-/

Bart Goesaert
Nice work so far, I've thought that on the fokker DR.I the airinlet for the engine was also behind the engine, in the 2 holes in the sideplates

Peter Jenssen 著者
Hi Bart,
I think for any rotating engine, the intake has to be at the back of the engine since the carburetor is in the axle.
What I think looks odd on the Camel is that the air intake is a large horizontal pipe running across the cockpit between the instrument panel and the pilot...
I guess you put things where there's room.. 😉

Peter Jenssen 著者
Hmm, wonder what this is?:
wingnutwings.com/ww/product?productid=3180
Given that clues for the next release are often in the background of the boxart of the previous release, perhaps something like this?:
facebook.com/1075528../?type=3&theater

Peter Jenssen 著者
I ordered an FE2b :-o
Rigging sanity challenger! 😉
Sadly it arrived with the box only half full.
7 sprues were missing!
On the positive side they (Weta) sent a replacement. A whole new kit.
I now feel the need to find something to do with the incomplete kit...
It has the fuselage (minus the bottom and the engine)
The wings (minus the struts)
The tail and booms (minus the cross beams and the elevator surfaces)
The clear sprue is missing. Also, the landing gear and the armament is missing..
Crash diorama? -or scratch missing pieces and build two?(!)

Need the struts and the gear, mainly, for a full build. (oh, and elevator control surfaces.)
The engine is available separately, as is the armament..
Hmm... -careful choice of variants..?

Mike Daniels
Yaaa. I want the WnW Fe2b. Like you say - mental rigging. Already watching.

Love the leather seat in the Camel.

Peter Jenssen 著者
Looks like they may have inadvertently supplied an exercise kit to practice on.. 🙂
The British rigging is a bit special in that it uses flat rigging wire.
Luckily I will get some practise with this on the Camel.. 🙂

Bart Goesaert
a dismantled casco? Nice gesture to provide a new kit altogether...

Peter Jenssen 著者
Very nice of them indeed. This was not technically from WnW, but from Weta. They seem to deal more in much more expensive collectables, where a replacement could easily be in the thousands of dollars.
Though, they did have some additional problems with my order. I ordered a different plane, paid, got shipment confirmation and then, later got an email that they had run out of that kit.
I picked this one as a replacement, which then arrived with the box half full.
So sending a whole new kit i probably compensation for all of this..
With a bit of effort, I can eke out two for the price of one out of this! 🙂
In the end, happy customer! 🙂
I ordered a Beardmore engine, if I build different versions, one clear sprue and one set of armaments can cover the needs of both kits. The fuselage bottom is completely flat, so that's easy to make.
Leaves the landing gear, the wing struts and the elevator control surfaces to scratch..

Peter Jenssen 著者
And, back to the Camel.
Decalling the tail, + some painting experiments.

Peter Jenssen 著者
Seatbelts done.
Carefully pre-drilling for rigging.

Spanjaard
OMG, this is attention to detail if i have seen one. i did not know how WnW was... amazing job you are doing.

Bart Goesaert
That's some serious seatbelt... nice work btw...

Peter Jenssen 著者
Thanks,
Yes, the seatbelt is a bit crude design.
Really wide, only tied around two cross timbers under the seat.
Still flying Camels don't seem to use these period seatbelts.. 🙂
Probably not a very good design.

Peter Jenssen 著者
Interior done!

Mike Daniels
That is so realistic.Worth spending the time on all those control lines. Looks great.

Alexander Grivonev
Those steering cables, holy cow!

Peter Jenssen 著者
Thanks!
And the closing of the fuselage is near..

Peter Jenssen 著者
-And on another note, Uschi van der Rosten just reported the new Wingnut kit is Junkers D1

Peter Jenssen 著者
Closing up, after making sure all control wires are in place.

Peter Jenssen 著者
Painting the engine. I dryfitted a bit as well to make sure the wings still fit.
I had to scrape some paint off to fit the lower wing.

Peter Jenssen 著者
I think I have done about 75 rigging lines so far and still haven't started on the wings yet... :-o

Mike Daniels
I am counting them one by one.

Peter Jenssen 著者
An attempt at the elusive PC10 colour.
I did some pre-shading. In fact spent an hour masking rib tapes for it. However, it is now barely visible.

Mike Daniels
I think that colour wise that looks about right Peter, if Dave Johnsons build on the WnW site is a good guide. Are you going to varnish it ? That would help to bring out the highlights and brighten up the texture. Nice prop!

wingnutwings.com/ww/..uctid=3157&cat=5

Peter Jenssen 著者
Thanks Mike,
I'll give it some very light olive accentuations with the airbrush I think, then we'll see after decalling. I don't want to put too many coats on, since the surface detail is so fine. Could easily get hidden by paint/too much clear. I've had some good experience with hand brushing very diluted acrylic clear.
Come to think of it, there are both half a fuselage and a wing section left in the box to experiment on... 🙂

Peter Jenssen 著者
Attaching the wing requires some extra putty and sanding.
Not been ably to put much time into the build recently, mostly slowly advancing with minor things that do not really need new photos.
Anyways, here's a picture of the wheels so far, not even these are actually done. Needs some clear and some more weathering.

Peter Jenssen 著者
Ready to put the lid on..

Peter Jenssen 著者
Attach cabane strut rigging before attaching top of fuselage. The top of the fuselage blocks access to the strut eyelets.

Peter Jenssen 著者
Rigging the tail

Peter Jenssen 著者
Set of wheels

Peter Jenssen 著者
Remember to decal the wings before attaching the ailerons or rudder horns! :-/

Bart Goesaert
nice work.. weren't rubber wheels in that time more dark grey then black?

Peter Jenssen 著者
Thanks!
The tyres did end up a bit dark. They are supposed to be Nato Black according to the instructions, but I think I might need to lighten them a bit.
I have done some weathering on the wheel covers, but none on the actual tyres. Hopefully it will look lighter when done...

Peter Jenssen 著者
Decal madness.. Pardon the mess... 🙂

Urban Gardini
Lovely work so far mate!

Mike Daniels
Finishing touches. Looks great!

Peter Jenssen 著者
Thanks!
One of the main finishing touches remaining;
Adding the upper wing and rigging it.. :-D

Peter Jenssen 著者
Here we go. Lots of lines!
To be honest, I may be doing a jet next (!)
I was going to do the Gotha or the Taube, but maybe a bit later..

Peter Jenssen 著者
Nearly there!

Peter Jenssen 著者
And the wing is on!
Not many details left now.
Windscreens, gunbarrels, a bit of weathering..

Spanjaard
rigging looking really nice

Tim Heimer
Wow, nice build, impressive!

Mike Daniels
Great finish Peter. The one to follow!! Great pics too.

Martin Oostrom
Great job Peter. She's delicious

Spanjaard
amazing result... what a patience and dedication!

Peter Jenssen 著者
Thanks everyone. As some may have suspected, this was actually completed a while back. Sorry for the lack of pictures. I'm afraid I just neglected that part and went straight to opening the next kit box instead... :-/

Gareth Windsor
Can't believe I missed this. What a fantastic build, very well done.

Peter Jenssen 著者
Thanks. It was a fun build. I recommend it! Surprising amount of rigging!

Peter Hardy
Peter, do you heave a sigh of relief or satisfaction when you finish a build like this? I think, if it were possible for me to build something like this, I would collapse in a pile of nervous relief. All credit to you Mate, Just brilliant!!!!!

Gordon Sørensen
Great looking Camel, Peter! Those Wingnut kits looks like they are well engineered.

Peter Jenssen 著者
Thanks guys!
The Wingnut kits are indeed very well engineered.
I keep doing dryfits, not to adjust and make the fit better as with other kits, no, the fit is usually perfect.
I keep making sure that I'm not ruining the fit in any way as I'm going along.
Famously, the Wingnut fit is so exact that even a thin coat of paint on mating surfaces can cause alignment problems.
-Peter; It is very satisfying to put a completed Wingnut model on the shelf, but also, the whole building process of these kits is a great experience. They have definitely put in effort to make it that way. Well researched options, great detail, fantastic instructions filled with plenty of references.
I keep taking the instructions out of the kits in my stash just to read. 🙂
The rigging is of course the tricky part, the sigh of relief is every time I let go of the Ez-line, and the CA holds the load! 🙂
I have been meaning to try different kinds of CA, but have not gotten around to it. Suspect the thin variety I'm using is not ideal...
(Accelerator does not work well for me)

Mike Daniels
Absolutely agree Peter. The WnW instruction booklets are fab. A lot of very hard to find historical information that is difficult to find elsewhere.

I have been using 'Gorilla' CA. Works well for me. Had a little tube that must have so far done about ten models. It is not runny at all and gives you a few seconds to move things around rather than being an instant bond.

Peter Jenssen 著者
I prefer it to cure fast. I'm using Zap thin CA. However, in drilled holes, it's a bit random how fast it cures. Sometimes it takes a minute or more, sometimes only seconds.
Trouble is, you can't tell until letting go of the line...
I had some issues with bonds cured with accelerator being weak, so I don't really trust it now.
Currently, I have resorted to working with a drop of glue on a piece of plastic that I have left out in the open for 15 minutes first.
Seems to be what works best for me so far...