U.S. Armored Tractor Bulldozer
Komentáre
38 23 October 2020, 00:42
Dave Beenak autorWill be slow going, but I expect to be well rewarded. This kit is off the charts.
23 October 2020, 00:45
Rui SI've all the time so I take a front row seat 👍
Does the kit have those tubes in the motor? 🤔
24 October 2020, 10:17
Dave Beenak autorProgress....piecing the controls together and trying to make it all connect up and look a little used. Once I have completed this part I think I will hit it with some matt varnish and finish off the engine/gearbox weathering detail before it all gets covered up with panels.
27 October 2020, 11:16
Dave Beenak autorSlowly covering up all the detail....at least I'll know what's in there.
29 October 2020, 11:03
Dave Beenak autorAt this point I would like to communicate my astonishment at some of the Miniart D7 builds that I have found on the web. Is it really that hard to study the technical drawings? Admittedly, there are alot of fiddly bits, but if you take your time to figure out how each part works with orientation to other parts, the instructions are pretty spot on. This is a challenging, but absolutely gold standard and rewarding build. I am quite prepared to put many months into this one to get the realistic finish that this kit deserves. Now all I have to do is keep the faith and forge on. Thanks for listening.
30 October 2020, 08:52
Dave Beenak autorI'm trying to be a little more subtle with the weathering this time (been known to go a bit overboard)....a new tractor put to work in 1943 would not have been too beaten up. I am doing the PTO version....I am assuming it would have been used in sandy type soil depending on the site.
3 November 2020, 08:25
Dave Beenak autorCable rigging parts just took 12 hours to complete. I'm taking my time to get it as close to right as I can.
7 November 2020, 09:20
Dave Beenak autorTracks fit perfect. Taking way more time than tank tracks....but should be worth the effort.
8 November 2020, 05:29
Dave Beenak autorWeathering the tracks was always going to make or break this project. Absolutely trying to replicate the worn natural steel look. No mud, just dry dust and a small amount of dirt buildup in the pins. Still have some minor work to do on these Friulmodel metal links.
11 November 2020, 07:46
Dave Beenak autorStarting to look the part. Going to use some metallics for the dozer blade.....wish me luck..!!
14 November 2020, 06:53
Dave Beenak autorok so that's it. Until I get around to drilling 700 x 0.5mm holes in the front radiator guard, that's it. Once I have a finished product I will take some propper photos and put 'em up.
16 November 2020, 11:10
OlivierThe photos so far are quite good. The next ones should make us dream.
16 November 2020, 13:35
Dave Beenak autorok so I took some preliminary photos in natural light to see what it looks like. I think it's ok for now. Still working on the front radiator protection plate. Not really finished with the weathering.....probably going to add some small amounts of dirt around the blade and track gear. I encourage any ideas for improvement. Thanks.
22 November 2020, 00:34
Rafael GonzalezStunning work. The whole subtle weathering with the absolutely spot on paint job it's just a joy to look at. Well done Dave 👌🏼
17 November 2023, 20:57
Lex JassiesGreat result Dave! 👍
I've build the D7 from Mirror models a few years ago. The Friul tracks you used look much better than the originals from Mirror or Miniart.
18 November 2023, 09:25
Dave Beenak autorThank you for the kind comments. This has been one of my favourite builds.
19 November 2023, 07:02
Album info
So.....the challenge begins.....this may take some time. Not going to rush this.
