Bü 131 eastern front recon Stab/NAGr.3

1
October 3, 2021
project inventory
2
October 3, 2021
the chosen subject: J0+?B
probably plain RLM71 oder RLM65 when compared to Revell's RLM70/71
copyright: "Embleme der Luftwaffe Bd.1" Richter - discussion only!
3
October 9, 2021
the Hirth engine looks great - a nice base for super detailing
4
October 9, 2021
5
October 9, 2021
fit is unfortunately not perfect
6
October 9, 2021
painted up
7
October 9, 2021
ready to hide behind the cowling
8
October 10, 2021
added the slot with a razor saw
9
October 10, 2021
linkage added from stretched sprue
10
October 14, 2021
seats: Quickboost vs. ICM
11
October 14, 2021
how the heck are you supposed to attah the QB seat?
the seatbelts are completely obstructing the attachment
12
October 14, 2021
deformed seatpan = more work
13
October 14, 2021
linkage for the throttle added
14
October 16, 2021
made a slot for the cross bar on the rear seat
15
October 16, 2021
after a dip in hot water and some force
16
October 16, 2021
how it should fit
17
October 16, 2021
Quickboost/Aires garbage - not even close
18
October 23, 2021
fit on the wings isn't great (upper one already scraped and sanded)
19
October 23, 2021
it gets worse further out - not what I expect from ICM!
20
October 23, 2021
black base for the interior
21
November 1, 2021
MRP RLM02 is on
22
November 1, 2021
23
November 1, 2021
I tried to paint the frames a tad lighter than the sidewalls to make them stand out
24
November 1, 2021
base colour for the wooden floor
25
November 1, 2021
There's wood!
26
November 6, 2021
27
November 13, 2021
28
November 13, 2021
port sidewall
29
November 13, 2021
starboard sidewall - still missing the trim cable
30
November 13, 2021
the Quinta RLM02 is a tad light
31
November 13, 2021
Quinta instrument panels
32
November 26, 2021
right side completed with the trim cable
33
November 26, 2021
Quinta belts are on
34
November 27, 2021
a view of the Quinta IPs
35
November 27, 2021
front coaming fitting fine on port
36
November 27, 2021
horribly wrong on the starboard side
37
November 27, 2021
some gentle force and we're good
38
November 27, 2021
seamwork on the belly
39
November 27, 2021
did someone ordere orange peel?
40
November 27, 2021
slowly getting there
41
November 27, 2021
orange peel as well
42
November 27, 2021
the nose before sanding and re-rivetting
43
December 4, 2021
starting to look like a Buecker
44
December 4, 2021
cowling rerivetted
45
December 4, 2021
not my best, but acceptable
46
December 4, 2021
opened the exhausts
47
December 4, 2021
added a new pitot and wires
48
December 5, 2021
graphics for the custom masks are drawn
49
December 7, 2021
all rigging anchor points marked up
50
December 7, 2021
51
December 11, 2021
black base is on
52
December 11, 2021
more CA to address the ghost seam
53
December 11, 2021
much better!
54
December 12, 2021
base for the insignia
55
December 12, 2021
same on the fuselage - not so sure about the position tho
56
December 21, 2021
starting point for the underside crosses
57
December 21, 2021
the masks marked for alignment
58
December 21, 2021
pulled the white part with frisket film
59
December 21, 2021
and applied
60
December 21, 2021
same for the upper wing
61
December 21, 2021
and the fuselage
62
December 21, 2021
preparing the tail band
63
December 21, 2021
and painted with MRP RLM04
64
December 21, 2021
the first aid compartment door got its red cross
65
December 21, 2021
starting the NAGr3 emblem with white
66
December 21, 2021
yellow roundel
67
December 21, 2021
and masked
68
December 22, 2021
and done!
69
December 21, 2021
red eagle (terribly out of focus, but you'll get the idea)
70
December 21, 2021
the overlapping letters need a negrative mask
71
December 21, 2021
Tamiya tape to help with the alignment
72
December 22, 2021
73
December 22, 2021
underwing crosses and codes masked
74
December 22, 2021
masks for the fuselage codes are on
75
December 27, 2021
marble coat is on
76
December 27, 2021
up close
77
December 27, 2021
everything blended together with Gunze RLM65
78
December 27, 2021
tried to keep it irregular
79
December 27, 2021
masks pulled - what a view!
80
December 27, 2021
up close, a little bleeding on the cross and small ridges around the numbers.
Will repair with a slight polishing
81
December 29, 2021
RLM71 applied
82
December 29, 2021
83
December 29, 2021
84
December 29, 2021
masks pulled
85
December 29, 2021
stupid mistake wit the O - need to retouch
86
December 29, 2021
small error with the first J
87
December 29, 2021
looks fine from afar
88
December 29, 2021
not so happy with the paint bleed this time
89
December 29, 2021
the emblem turned out fantastic
90
January 30, 2022
Revell's decals really don't conform to the surface and are way too thick
91
January 30, 2022
decals applied
92
February 8, 2022
Added the eyelets as rigging anchor points.
Making all of them by twisting 0.2 mm copper wire took a while
93
February 12, 2022
luckily the original turnbuckles were heidden inside the cowling-less work for me
94
February 12, 2022
all rigging lines attached to the upper wing
95
February 12, 2022
the first one finished on the elevators
96
February 25, 2022
97
February 25, 2022
98
February 27, 2022
99
February 27, 2022
100
February 28, 2022
101
February 28, 2022
102
March 5, 2022
103
March 5, 2022
104
March 5, 2022
105
March 5, 2022
106
March 5, 2022
107
March 5, 2022
108
March 5, 2022
109
March 5, 2022

Komentáre

30 3 October 2021, 09:18

Giannis Kaltapanidis
Interesting build! Quinta's decals realy do the job!

4 December 2021, 12:20

Joachim F. autor
Yeah, they are a mighty fine and most of all a quick addon!

11 December 2021, 16:08

Felix
Following 👍🏻

11 December 2021, 21:03

Gordon Sørensen
Great work on this kit, Joachim. The Quinta details look very nice.

27 December 2021, 13:11

Joachim F. autor
Thanks Gordon - I'd place the Quinta details between precoloured PE and textile belts + individual instrument decals with the Quninta thingies the least work of the three 😉

27 December 2021, 17:07

Harvey H.W.
Tons of details！

12 February 2022, 16:23

Rui S
I'm in 😎

12 February 2022, 17:26

Lochsa River
sittin in....

27 February 2022, 07:55

Dietmar Bogatzki
Fantastic rigging, Joachim 👍

27 February 2022, 08:49

Guy Rump
Great rigging 👍

27 February 2022, 16:33

Joachim F. autor
Thanky guys - this was a first time for me and there's some room for improvement (especially with the line type), but it was a lot of fun to pull all the lines through the eyelets and see it coming together!

28 February 2022, 09:15

Gordon Sørensen
Great work on the flying wires! The eyelets really add to the look.

28 February 2022, 12:26

Neuling
Top result!

5 March 2022, 11:00

Joachim F. autor
Thanks mates! I'll try tu use some thinner line next time to be able to pull the lines through the eyelets and the tubes!

6 March 2022, 07:35

Project info

Bü 131 Jungmann Stab/NAGr.3

109 snímky

1:32

dokončený

1:32 Bü 131 Jungmann - Seats w/ Seatbelts (Quickboost QB 32 219)

1:32 Bu 131 interior 3D decals (Quinta Studio QD32016)

Všetky albumy

Zobraziť všetky albumy »