Gloster Meteor NF.14

Sword | No. SW48011 | 1:48

Gerçekler

Marka:: Sword
Başlık:: Gloster Meteor NF.14
Numara:: SW48011
ölçek:: 1:48
tip:: Tam kiti
Yayınlandı:: 2020 Yeni araç
Barkod:: 8596444480116 (EAN)
konu:: Gloster Meteor » jetler (uçak)

İşaretleri

Gloster Meteor

Gloster Meteor NF Mk.14

Royal Air Force (1918-now)

No. 72 Sqn. WS833/MS (Wg.Cdr. Maurice Shaw)
1956 - RAF Church Fenton
BS381C:241 BS381C:638 BS381C:627
No. 85 Sqn. WS776/J (Sq. Ldr. Miroslav Liškutin)
1958 - RAF Church Fenton
BS381C:241 BS381C:638 BS381C:627

Kutu içeriği

boyutlar:
420x205x65 mm (16.5x8.1x2.6 inch)

Ağırlık:
363 g (0.8 lbs)

tarafından tasarlanan Boxart Jerry Boucher

Ürün zaman çizelgesi

Sword

2020

Yeni araç

Tam tarih »

Talimatlar

İndir 7205Kb (.pdf)

Pazaryeri

Çevrimiçi mağazalar

USD 51.81Stokta var »

Tüm teklifleri göster » (12 toplamda)

Özel ticaret ve takas

EUR 36.00

Satıcıyla iletişime geç

Alternatif SKU'lar Sword SW48011:
SW-48011 | 48011 | SWORD48011 | SWD48011 | SRT48011

Not: Fiyatlar ve uygunluk sadece göstergedir. Ürünün gerçekten aynı olup olmadığını da kontrol edin!

İlgili ürünler

A.W. Meteor NF Mk.14 Canopy Airbrush Mask for Sword

MH Models 1:48

X48097

Meteor NF.14 nose

LACO 1:48

LAC48 tba 2020* Yeni araç

Meteor NF.14 EXPERT kabuki masks for Sword

New Ware 1:48

NWAM0720 2020 Yeni araç

Meteor NF.14 ADVANCED kabuki masks for Sword

New Ware 1:48

NWAM0719 2020 Yeni araç

Dervent-V

KEPmodels 1:48

KMU48011 2023 Yeni araç Çok konu (2)

Tüm ilgili ürünler » (27 toplamda)

Kutu içi incelemeler

Dış incelemeler

reklâm

Kutu içi inceleme

KFS-miniatures

Kutu içi inceleme

Hyperscale

gözden geçirmek

KFS-miniatures

gözden geçirmek florymodels

Tüm incelemeler » (5 toplamda)

Dergiler

Model Airplane International | 180

English (TOC: 6 lines)

July 2020

Scale Aircraft Modelling | Volume 42, Issue 11

English (TOC: 8 lines)

January 2021

Wingmasters | 143

French (TOC: 8 lines)

September-October 2021

tüm dergiler » (4 toplamda)

Yorumlar

Gluefinger
I was just about to begin to put the decals on this thing when I realized they mis-numbered a large part of smaller decals (of which there are a lot) in the instruction sheet. Worst of all, there seems to be no logic to the mis-numbering, such as a fixed offset...
Now I have to spend hours to find out which goes where.

Thank you, Sword, for ruining what so far was a quite enjoyable build.
If you, or a test subject, had built the model just once, using your own instructions, this would immediately have become obvious.
I suggest you peruse the following Wikipedia article before p*ssing off more customers with something that is easily avoidable:
en.wikipedia.org/wiki/Quality_control

1 17 October 2021, 14:00